Learn R Programming

Hmisc (version 5.1-3)

redun: Redundancy Analysis

Description

Uses flexible parametric additive models (see areg and its use of regression splines), or alternatively to run a regular regression after replacing continuous variables with ranks, to determine how well each variable can be predicted from the remaining variables. Variables are dropped in a stepwise fashion, removing the most predictable variable at each step. The remaining variables are used to predict. The process continues until no variable still in the list of predictors can be predicted with an \(R^2\) or adjusted \(R^2\) of at least r2 or until dropping the variable with the highest \(R^2\) (adjusted or ordinary) would cause a variable that was dropped earlier to no longer be predicted at least at the r2 level from the now smaller list of predictors.

There is also an option qrank to expand each variable into two columns containing the rank and square of the rank. Whenever ranks are used, they are computed as fractional ranks for numerical reasons.

Usage

redun(formula, data=NULL, subset=NULL, r2 = 0.9,
      type = c("ordinary", "adjusted"), nk = 3, tlinear = TRUE,
      rank=qrank, qrank=FALSE,
      allcat=FALSE, minfreq=0, iterms=FALSE, pc=FALSE, pr = FALSE, ...)
# S3 method for redun
print(x, digits=3, long=TRUE, ...)

Value

an object of class "redun" including an element "scores", a numeric matrix with all transformed values when each variable was the dependent variable and the first canonical variate was computed

Arguments

formula

a formula. Enclose a variable in I() to force linearity. Alternately, can be a numeric matrix, in which case the data are not run through dataframeReduce. This is useful when running the data through transcan first for nonlinearly transforming the data.

data

a data frame, which must be omitted if formula is a matrix

subset

usual subsetting expression

r2

ordinary or adjusted \(R^2\) cutoff for redundancy

type

specify "adjusted" to use adjusted \(R^2\)

nk

number of knots to use for continuous variables. Use nk=0 to force linearity for all variables.

tlinear

set to FALSE to allow a variable to be automatically nonlinearly transformed (see areg) while being predicted. By default, only continuous variables on the right hand side (i.e., while they are being predictors) are automatically transformed, using regression splines. Estimating transformations for target (dependent) variables causes more overfitting than doing so for predictors.

rank

set to TRUE to replace non-categorical varibles with ranks before running the analysis. This causes nk to be set to zero.

qrank

set to TRUE to also include squares of ranks to allow for non-monotonic transformations

allcat

set to TRUE to ensure that all categories of categorical variables having more than two categories are redundant (see details below)

minfreq

For a binary or categorical variable, there must be at least two categories with at least minfreq observations or the variable will be dropped and not checked for redundancy against other variables. minfreq also specifies the minimum frequency of a category or its complement before that category is considered when allcat=TRUE.

iterms

set to TRUE to consider derived terms (dummy variables and nonlinear spline components) as separate variables. This will perform a redundancy analysis on pieces of the variables.

pc

if iterms=TRUE you can set pc to TRUE to replace the submatrix of terms corresponding to each variable with the orthogonal principal components before doing the redundancy analysis. The components are based on the correlation matrix.

pr

set to TRUE to monitor progress of the stepwise algorithm

...

arguments to pass to dataframeReduce to remove "difficult" variables from data if formula is ~. to use all variables in data (data must be specified when these arguments are used). Ignored for print.

x

an object created by redun

digits

number of digits to which to round \(R^2\) values when printing

long

set to FALSE to prevent the print method from printing the \(R^2\) history and the original \(R^2\) with which each variable can be predicted from ALL other variables.

Author

Frank Harrell
Department of Biostatistics
Vanderbilt University
fh@fharrell.com

Details

A categorical variable is deemed redundant if a linear combination of dummy variables representing it can be predicted from a linear combination of other variables. For example, if there were 4 cities in the data and each city's rainfall was also present as a variable, with virtually the same rainfall reported for all observations for a city, city would be redundant given rainfall (or vice-versa; the one declared redundant would be the first one in the formula). If two cities had the same rainfall, city might be declared redundant even though tied cities might be deemed non-redundant in another setting. To ensure that all categories may be predicted well from other variables, use the allcat option. To ignore categories that are too infrequent or too frequent, set minfreq to a nonzero integer. When the number of observations in the category is below this number or the number of observations not in the category is below this number, no attempt is made to predict observations being in that category individually for the purpose of redundancy detection.

See Also

areg, dataframeReduce, transcan, varclus, r2describe, subselect::genetic

Examples

Run this code
set.seed(1)
n <- 100
x1 <- runif(n)
x2 <- runif(n)
x3 <- x1 + x2 + runif(n)/10
x4 <- x1 + x2 + x3 + runif(n)/10
x5 <- factor(sample(c('a','b','c'),n,replace=TRUE))
x6 <- 1*(x5=='a' | x5=='c')
redun(~x1+x2+x3+x4+x5+x6, r2=.8)
redun(~x1+x2+x3+x4+x5+x6, r2=.8, minfreq=40)
redun(~x1+x2+x3+x4+x5+x6, r2=.8, allcat=TRUE)
# x5 is no longer redundant but x6 is
redun(~x1+x2+x3+x4+x5+x6, r2=.8, rank=TRUE)
redun(~x1+x2+x3+x4+x5+x6, r2=.8, qrank=TRUE)

# To help decode which variables made a particular variable redundant:
# r <- redun(...)
# r2describe(r$scores)

Run the code above in your browser using DataLab